如何安裝變極器-中英對照
如果設備損壞或任何元件缺失，請不要安裝和操作變極器。
這樣做會導致電擊或火災。請求助當?shù)卮硖庍M(jìn)行維修。
強制性的 •必須安裝于不可燃燒的條件下，如：金屬環境。
后面板會非常熱，因此如果安裝于易燃的環境中既有可能導致火災。
•請勿在前面板被移開的情況下操作設備。這樣可能會
•必須安裝緊急停止裝置，該裝置要與系統規格匹配（例如：切斷輸入電源，然后使用機械制動。）
在變極器單獨操作的情況下不能立即停止操作，因?yàn)榇嬖谝馔夂腿松韨Φ目赡堋?br />
•所有使用的選項都必須由Toshiba公司規定。使用其他的選項可能會導致意外事故的發生。
警告
強制性的 •主要裝置必須安裝在基座上，該基座要能夠承受裝置的自身重量。
如果裝置安裝于一個不能承受自身重量的基座上，裝置可能滑落并造成人身傷害。
•如果有必要制動（支撐電機軸），請安裝一個機械制動器。變極器上的制動裝置將不能作為機械支撐之用，而且如果用于支撐的話，可能會導致人身傷害。
■ 安裝位置
選擇通風良好的室內作為安裝地點，在垂直的方向縱向放置設備并附加一個金屬壁表面。
如果你安裝的變極器數量不止一個，兩個變極器之間要分開，且距離至少為5分米，并水平方向排列。
如果變極器按照水平方向排列，而且之間沒有留出空隙（一個挨著一個的安裝方式），去除變極器頂部的通風密封，并在40℃或40℃以下溫度中操作（3.7 kW模式或更低）。在50℃或50℃以下溫度中操作（5.5 kW模式或更高）。
•標準安裝 •水平安裝（一個挨著一個的安裝方式）
圖中文字翻譯：5 centimeters or more：5厘米或更長
10 centimeters or more 10厘米或更長
Remove seals on top 移開頂部的密封
Ambient temperature of 40℃ or less (model of 3.7 kW or less)
環境溫度40℃或40℃以下（3.7 kW模式或更低）
Ambient temperature of 50℃ or less (model of 5.5 kW or less)
環境溫度50℃或50℃以下（5.5 kW模式或更高）
圖中所示的間隔為最小允許間隔。因?yàn)樵诳諝饫鋮s裝置的頂部或底部表面安裝有許多冷卻風扇，盡可能使得頂部和底部的空間更大以便留出一條通風通道。
8-5-029-029
注意事項：不允許在任何高濕度或高溫度以及存在大量灰塵，金屬碎片和油霧的條件之下安裝設備。如果你即將在某地方安裝設備，而該地區存在潛在的問題，請?jiān)诎惭b之前與Toshiba公司聯系。
■ 變極器的熱值和通風要求
變極器從交流電轉換成直流電，然后又轉換回交流電的能量損失大約為5%。當損失轉化為熱量損失時，為了抑制配電室中溫度的上升，變極器必須進行通風和冷卻處理。
當在密封的配電室中運行時，要求一定的壓氣冷卻通風量和散熱量。電機功率如下：
電壓等級 操作電機功率（kW） 變極器類型 熱值 要求壓氣冷卻通風量 密封配電室所需的散熱表面積（m2）
載波頻率
4kHz 載波頻率
12kHz
單相
200V 級 0.2
注意事項
1) 外部裝置（進線電抗器，直流電抗器和無線電降干擾過濾器等）的熱損失不包含在本表的熱值之內。
2） 100%負載連續操作情況
■ 面板設計必須考慮干擾的影響。
變極器產生高頻干擾。當設計控制面板裝置時，必須將干擾列入考慮范圍內。測量方法如下：
•接線以便主電路電線和控制電路電線分開。切勿將兩種電線放入統一個導管內，不要讓電線平行放置，也不要困扎電線。
•為控制電路接線提供屏蔽導線和絞線。
•將主電路的輸入（功率）和輸出（功率）電線分開。不要讓電線平行放置，也不要困扎電線。
•將變極器接到接地引線上 。
8-5-029-030
•在任何一個電磁開關上安裝電泳抑制器，且在變極器周圍使用線圈。
•如有必要，安裝降噪過濾器。
•安裝EMC板（符合附件標準），同時屏蔽導線要與EMC板相適合。
How to install
i
^ Danger
<S>
Prohibited • Do not install and operate the inverter If it is damaged or any component is missing. This can result in electric shock or (ire. Please consult your local agency for repairs.
o
Mandatory • MUSI be installed in nonllammables such as metals. The rear panel gets very hot so that if installation is in an inflammable object, this can result in (ire. • Do not operate wilh the front panel cover removed. This can result in electric shock. • An emergency stop device must be installed that fits wilh system specifications (e.g. cuts off input power then engages mechanical brakes). Operation cannot be stopped immediately by the inverter alone, thus risking an accident or injury. • All options used must be those specified by Toshiba. The use ol any other option may result in an acci¬dent.
/?\ Warning
O
Mandatory • The main unit must be installed on a base that can bear the unit's weight It the unit is installed on a base that cannot withstand that weight, the unit may (all resulting in injury. • II braking is necessary (to hold motor shaft), install a mechanical brake. The brake on the inverter will not function as a mechanical hold, and if used (or that purpose, injury may result.
Installation location
Select a location with good indoor ventilation, place lengthwise in the vertical direction and attach to a metal wall surface.
If you are installing more than one inverter, the separation between inverters should be at least 5 centime¬ters, and they should be arranged in horizontal rows.
If the inverters are horizontally arranged with no space between them (side-by-side installation), peel of the ventilation seals on top of the inverters and operate at 40°C or less (model of 3.7kW or less). Operate at 50°C or less (model of 5.5kW or more).
Standard installation
Horizontal installation (side-by-aide installation)
10 centimeters or more
5 centime I ers or more
10 centimeters or more
1 ' i • 10 centimeters or more Remove seals on top
a of 40'C a less (motW ol 3 7kW a l»il ra ol 50°C or IMS (modd ct 5 SkW a man)
VFS9 VFS9 VFS9 Ambienl fornfioralL r Arnbterrt Inmparatt.
The space shown in the diagram is the minimum allowable space. Because air cooled equipment has cooling lans built in on the lop or bottom surfaces, make the space on top and bottom as large as possible to allow for air passage.
A-1B
TOSHIBA
Mole: Do not install in any location where (hare is high humidity or high temperatures and where there are large amounts of dusl, metallic fragments and oilmist If you are going to install the equipment in any area that presents a potential problem, please consult with Toshiba before doing so.
I Calorific values of the inverter and the required ventilation
The energy loss when me inverter converts power from AC to DC and then back to AC is about 5 percent. In order to suppress the nse in temperature inside the cabinet when this loss becomes heal loss, the interior of the cabinet must be ventilated and cooled.
The amount of forcible air cooling ventilation required and the necessary heat discharge surface quantity
when operatin in a sea ed cabinet accord.nq to motor capacity are as follows
Voltage Class capacity Inverter Type (rClm" hC*™ . . ,...:'-• - WMfM^Mto'lMM
2002PL 23 29 23
200V Class s VFS9S- 2007PL 201 5PL 142 SB 169 40 60
2022PL 239 so
5 i " 29
200V Class VFS9- 330 195 374 f
2055PL 450 7
2075PL 676 635 3
] 2150™ 750 1035 ;' |
° 2015PL 77 59 60
2022PL 103 134 80
400V Class VFS9- 2QE5PL 264 354 7
If 2075PL 2150PL i BOB ,; ;
Notes
tor. DC reactor, radio
1 ) The heat loss lor the optional external devices (input re
etc.) is not included in the calorific values in the table. 2) Case of 100% Load Continuation operation.
rol panel setup, consideration musl be parated. Do not place Ihem in the
I Panel designing taking into consideration the effects of noise.
The inverter generates high frequency noise. When designing th given to that noise. Examples of measures are given below.
• Wire so that the main circuit wires and the control circuit wires
same conduit, do not run them parallel, and do not bundle them
• Provide shielding and twisted wire for control circuit wiring.
• Separate the input (power) and output (motor) wires of the main circuit. Do not place them in the
conduit, do not run them parallel, and do not bundle them.
• Ground the inverter ground terminals (i).
TOSHIBA
> Install surge suppressor on any magnetic contactor and relay coils used around Ihe in
• Install noise filters if necessary.
. Install EMC plale (attached as standard) and shielded wires fit with the EMC plate.
2012.12.22