蓄冰設備調試準備標書翻譯-中英對照
3. Preparations for Ice Storage Devices Debugging
1） 配合業主調試工作安排
1)  Debugging arrangement which assorts proprietors
調試前完成所有蓄冰設備安裝及驗收工作，積極參加相應業主、監理及機電總包單位和廠商成立的聯合調試工作小組工作，組織工程技術人員按時參加調試準備會議，按計劃和審定詳細調試步驟和操作程序，做出具體的調試安全防范措施，并由我公司進行蓄冰設備技術和責任澄清及協調工作。
Complete all the installment of ice storage devices and acceptance work; take part in the work by the united debugging team which is set up by relevant proprietors, supervisors, electromechanical general address contractors and manufacturers actively; organize engineering technical personnel to attend the debugging conference on schedule; work out specific debugging safety alarm measures according to the planned and audited detailed debugging steps and operation program; the technologies, responsibility declaration and coordination of ice storage device should be carried out by our company.
2） 現場調試準備工作
2） On-the-spot Preparation for Ice Storage Devices Debugging
①. 檢查調試檢測所用儀器及工機具是否齊全，良好。
②. 檢查并確定設備和系統是否已按設計要求和生產廠家的書面安裝規范進行正確安裝。
③. 檢查管道系統是否已進行正確清洗，預處理和充注。
④. 現場照明條件應完善，各燈應能正常開關。
⑤. 檢查各系統閥門及控制點安裝位置是否正確合理，開關是否靈活。
⑥. 機房場地應清掃干凈，無其它雜物堆放，排水溝應暢通�？刂七M(jìn)入現場人數，非工作人員不得入內，并設告示牌。調試期間各設備掛牌警示。
⑦. 安全防范措施要具體，消防用品備齊。
1) Check and make sure that devices, machines and tools are all ready and in good condition.
 2) Check and make sure that devices and systems are installed according to the design requirements and manufacturers’ written installation specification.
 3) Check if the ductwork has been cleaned, pretreated and filled properly
 4) The lighting condition on-the-spot should be perfect and all lights can be turned on and off normally.
 5) Check if valves and reference points of every system have been installed properly and if the switches respond well to the controls.
 6) Equipment room should be cleaned without any sundries and the barrel-drains should be expedited. Control the number of people on the spot, make sure only staff can get in there and set up notice boards. All devices should be attached with alarming boards during the debugging period.
 7) Safety and protection measures should be detailed and fire control store should be complete.
2、 調試步驟
4. Debugging Steps
①. 蓄冰設備調試應按先手動后自動；先分部后系統的原則展開：
②. 調試前檢查→設備單項手動調試→工況分部手動調試→系統聯合手動調試→設備單項自控調試→自控點單項聯動調試→聯合自控調試。
1) Ice storage devices should be debugged manually and then automatically, partially and then generally.
 2) Check before debugging → device debugging singly and manually → operating mode debugging partially and manually → system debugging generally and manually → device debugging singly and automatically → automatic reference points debugging singly and generally → debugging generally and automatically.
3、 蓄冰系統試運行
5. Ice Storage System Trial Operations
1) 蓄冰工況試運行
1）Ice Storage Operating Mode Trial Operations
①. 依工況設置打開電動閥，啟動冷卻水循環泵，再啟動冷凍水循環泵，乙二醇循環泵，同時開啟與上述閥門相連的手動蝶閥。待所有的泵正常工作三分鐘后，再開啟雙工況冷水機，使其置于制冰工況運行。
②. 觀察蓄冰盤管的結冰情況。在冷機工作正常的情況下，從蓄冰槽頂?shù)娜丝卓�，冰盤管上的結冰量應是逐漸增厚的。
③. 觀察冰厚度控制器所顯示冰量情況。
④. 觀察蓄冰系統在低溫工況下保溫材料表面是否有結露現象。
⑤. 停機，停機后15分鐘停泵。
1) Set opening the electronic calve according to the setting of operating modes, start up the cooling water circulation pump, the freezing water circulation pump, and the glycol circulation pump and turn on the manual butterfly valve which is attached to the electronic calve. After three minutes of normal operation of all the pumps, start up the double modes water chilling machine by setting up the ice generating mode.
 2) Observe the icing conditions of the ice storage plate. In the condition that the refrigerating machine runs well, watch from the manhole on the top of the ice bunker to make sure that the ice in the ice storage plate should be thickened gradually.
 3) Observe the ice volume showed in the ice thickness controller.
 4) See if there is dew in the face of the heat insulator when the ice storage system is working with low temperature.
 5) Turn off the machine and 15 minutes later turn off the pumps.
2) 制冷機與蓄冰槽同時供冷
2）Refrigerating Machine and Ice Storage Bunkers Supply Cold Simultaneously
①. 依工況開啟調節相應的電動閥，并同時開閉有關的手動閥門，先啟動冷凍水循環泵，然后啟動乙二醇循環泵，冷卻水循環泵，待所有的泵和閥工作正常后三分鐘，啟動冷水機組。
②. 停機后15分鐘停泵。
1) Adjust relevant automatic valves according to the operating mode and meanwhile turn off relevant manual valves. Start up the freezing water circulation pump, and then the glycol circulation pump and the cooling water circulation pump. After three minutes of normal operation of all the valves and pumps, start up the water chilling unit.
 2) After the unit has been turned off for 15 minutes, turn off the pumps
3) 蓄冰槽供冷
3. Cold Supply of Ice Storage Bunkers
①. 依工況開啟和關閉相應閥門。
②. 啟動冷水循環泵，再啟動冷凍水循環泵。
③. 觀察供冷板換進出口的溫度是否為設計溫度，否則，調節閥門，使其合乎要求。
1) Turn on or off relevant valves according to the operating modes.
 2) Start up the cooling water circulation pump and then the freezing water circulation pump
 3) See if the temperature of scavenge port of the cold supply board is as it was planned. If not, adjust the valve to set the temperature according to what it is required.
4、 配合蓄冰自動控制系統調試
6. Debugging to Support the Automatic Ice Storage Control System
配合有關單位查看現場控制機及各冷水機組受控蓄冰設備投入樓宇自控運行狀態，結合上位機操作進行系統聯機試運行，記錄蓄冰設備運行工況，其間主要測試項包括：
Support relevant parties to check the on-the-spot conditions of controllers and all the controlled ice storage devices of water chilling units used in building automatic operation. Implement system online trial operation by combining computer operation. Write down operating modes of ice storage devices. Relevant testing items include:
 根據工況和時間設定自動調整蓄冰運行狀態
 自動檢測冷凍水、冷卻水供、回水溫度、壓力
 自動檢測回水溫度、壓力
 自動檢測軟化水箱、凝結水箱高低液位
 自動控制補水泵啟停并檢測其運行狀態
 自動控制循環水泵啟停并檢測其運行狀態
 可實現手/自動狀態轉換
 故障報警
 可通過中央管理工作站對其進行遠動控制與管理
 Set automatically adjusted ice storage operating condition according to operating modes and time
 Automatically check the temperatures and pressures of the supplying and returning freezing water and cooling water
 Automatically check the temperatures and pressures of backwater
 Automatically check the high and low liquid levels of demineralized water tanks and condensed water tanks
 Automatically control the turn-on and turn-off of the supply pump and its operating conditions
 Automatically control the turn-on and turn-off of the water circulating pump and its operating conditions
 Manual and automatic conditions are realizable
 Trouble alarm
 Remote control and management are obtainable by the central management workstation
5、 調試結果
7. Debugging Results
蓄冰設備調試試運行正常后做出書面報告，由參與人員簽字確認，填寫調試報告送呈建設方和監理方確認存檔。
Work out written report after the proper trial operation of debugging ice storage devices and the report should be signed by participators. Fill in the debugging report and deliver it to the constructors and supervisors to be affirmed and filed.
一、 設計圖紙-附后
IV. Design drawing - attached

武漢翻譯公司報價

2012.12.2