終端面板和繼電器-中英對照

終端面板和繼電器面板必須設置在至少離控制柜底部 80毫米位置。對全部終端進行標識。
3.在控制柜內導線必須排列整齊并且用系帶系牢。
4.地接電路導線可以使用連續的白色或者自然的灰色。
5.設備接地導線可以通過純綠色的顏色或者通過連續的綠色的顏色用一條或更多條黃色色帶標識。
G.交通信號頭：
1.將信號頭連接到支持架上；按照?qǐng)D紙安裝定位。
2.將信號頭對向交通控制方向。 燈光的中線應該先于停車站線大約50米和在交通中心接近；
H.檢測器環路的安裝：按照?qǐng)D紙要求安裝檢測器環路設備，此中確切說明，根據制造商的指示，適用的電氣代碼要求并采用認可的工業慣例。
涂裝： 安裝圖紙的要求或者第09875 部分"抗腐蝕薄層"指定的要求，對電鍍和非鍍膜黑色金屬進行底漆和最后涂裝，取較嚴格的標準為準：
第1層涂裝： 底漆。
第2層涂裝： 高光澤醇酸搪瓷。
第3層涂裝： 高光澤醇酸搪瓷。
第1層涂裝不需要在車間進行底漆涂裝。涂層總厚度將不小于0.1毫米，在涂裝前徹底進行表明清潔。
電鍍鋼材必須按照批準的程序進行預處理，保證涂層適當?shù)膲壕o度。 顏色為深黃色。
在控制柜內的導線必須安排整齊并且用系帶系牢。
地接電路導線可以使用連續的白色或者自然的灰色。
設備接地導線可以通過純綠色的顏色或者通過連續的綠色的顏色用一條或更多條黃色色帶標識。
2. Panels for terminals and relays to be located at least 80 mm from bottom of cabinet. Identify all terminals adequately.
3. Wiring within controller cabinet to be neatly arranged and laced.
4. Grounded circuit conductor shall be identified by continuous white or natural grey color.
5. Equipment grounding conductor shall be identified by solid green color or by continuous green color with one or more yellow strips.
G. Traffic Signal Heads:
1. Attach signal heads to support; located, arranged, and directed as specified on drawings.
2. Point signal heads in direction of approaching traffic to be controlled. Direct centre of light beam toward approximately 50 meters in advance of stop line and in centre of traffic approach;
H. Installation of Detector Loop: install detector loop devices as shown on approved drawings, specified herein, in accordance with manufacturer's instructions, applicable requirements of the Electrical Code and in accordance with recognized industry practices.
Painting: Carry out priming and finish painting of galvanized and uncoated ferrous metal as follows or conform to requirements of Section 09875, "Corrosion Resistant Coatings", whichever more stringent:
1st coat: Prime coat.
2nd coat: High gloss alkyd enamel.
3rd coat: High gloss alkyd enamel.
First coat not required on items delivered shop primed. Total dry film thickness shall not be less than 0.1 mm. Carry out cleaning and priming prior to installation.
Galvanized steel shall be pre-treated with an approved system to ensure proper bonding of the paint coating. Color shall be dark yellow.
Wiring within controller cabinet to be neatly arranged and laced.
Grounded circuit conductor shall be identified by continuous white or natural grey color.
Equipment grounding conductor shall be identified by solid green color or by continuous green color with one or more yellow strips.
2014.10.14