閘門儲存間技術規格翻譯-中英
儲存間導槽用來豎向儲存閘門。導向裝置包括固定在儲存坑墻壁的搭接片和角鋼部件。導向裝置安裝在操作平臺之下，并維持在一個垂直位置上。導向裝置的支承塊把閘門支撐在坑底之上，并且使密封與混凝土結構不接觸。支撐塊有塑料表面，以防止與閘門接觸時保護層使閘門涂漆層受損傷。2個HPX泵房設置8個儲存間，共儲存16個閘門，寬度5.5m*；
d） 鼓形濾網
鼓形濾網設備應該遵循 RCC-M 等級3。
1）概述
鼓形濾網是一個在圓周上裝有網片的旋轉圓筒體。水從兩側端面進入鼓形濾網，經過網面過濾后沿圓周向外出水。當鼓形濾網旋轉時，將網面攔截的污物帶到操作平臺以上，用沖洗水沖入排污槽，通過排水溝道排走。旋轉結構是由鼓網框架構成的，通過安裝在主軸上的輪轂上向外發散的輻條支撐。主軸兩端用密封的軸承座里油潤滑的自動調心雙列球面滾子軸承支撐。主軸一端的軸承座中，裝有外加電流陰極保護系統的電刷式饋電機構。鼓形濾網兩側設有帶低油位報警開關的潤滑油箱。濾網的的外圓面由單獨的、可更換的網片組成，網片用螺栓和螺母固定于鼓形濾網骨架的圓周上。
鼓形濾網旋轉時的密封，是由用壓板、緊固件安裝在骨架結構外環上的柔性成型橡膠密封板，與安裝在水室墻壁上的固定密封角鋼上的低摩擦密封板相接觸實現的。
撈污斗固定在鼓形濾網內的水平橫梁上，提升大塊污物。通往鼓形濾網反沖洗水清洗裝置的操作平臺上設有欄桿，從操作平臺通道，防濺罩，排污裝置到運行平臺的通道上都設有樓梯。安裝在防濺罩里的反沖洗管為兩個100％容量的管路，掀開防濺罩的折葉蓋板可對噴嘴進行檢查檢修。
當鼓形濾網旋轉時，網片轉過鼓形濾網內部的排污斗時，被一系列安裝于鼓形濾網全寬的網片上方的噴嘴沖洗。噴嘴以快換接頭與反沖洗管相接，易于清洗、更換。反沖洗管上帶有測壓儀表。收集在排污斗內的污物和沖洗水通過一混凝土排水溝道排走。鼓形濾網由驅動裝置傳動軸上的小齒輪，驅動鼓形濾網骨架結構中央環上的大齒圈旋轉。傳動軸由一對可分滾子軸承支撐，與組合減速器聯接，減速器由獨立的低速和雙速（中/高速）電機驅動。還有一個備用的低速電機安裝在減速器用于緊急備用。通過安裝在別處的主控盤上的電子功率監測器跳閘來實現驅動裝置扭矩過載保護。電動機帶有防潮加熱器。為了防止在由高速向中速轉換或中速向低速轉換時低速電機產生負電勢，在每個低速電機上安裝一個測速發電機以獲得一個與驅動速度成比例的信號。在速度達到同步轉速之前，控制系統將協調控制，以防止中低速電機接電。
2） 廠址數據
設備形式 室內安裝
過濾介質 海水
運行平臺 8.50 m
外海潮位為：
SEC 設計最高潮位 7.58m
CRF 設計最高潮位: 4.54 m
CRF 設計最低潮位: -1.47m
SEC 設計最低潮位: -3.35m
泵房前池（海水庫）水位為：
CRF 設計最低水位: -6.72m
SEC 設計最低水位: -8.00m
鼓網中心線標高 -1.0m*
進水渠寬度 5.5m*
進水渠底標高 -11.5m*
進水腔水室寬度 6.0m*
濾網腔室底標高 -17.1m*
3） 水力數據
流量 24.2m3/s*
進水口流速
過網流速
進水口水頭損失
過網水頭損失
總水頭損失
4） 鼓形濾網參數
鼓形濾網數量 8臺（每機組4臺）
直徑 22m*
水室土建結構凈寬 6.0m*
設計水位差 2.0m
網孔直徑 3mm
操作平臺標高 8.0m*
鼓形濾網在操作平臺以上高度 2m*
沖洗管數量 2
沖水管直徑 mm
沖洗水流量 L/s
沖洗管內水壓
5） 工程的材料
結構 碳鋼
主軸 鍛造碳鋼
沖洗水噴嘴 不銹鋼 316L
沖洗管 不銹鋼 316L
10） The technical specification of guide barrel of strobe storage room
The guide barrel of storage room is used to store the strobe vertically. The guiding device includes splice plate and angle steel part which are fixed to the wall of storage room. The guiding device is installed below an operation platform, keeping in a vertical position. The supporting block of guiding device upholds the strobe above the pit base, avoiding the seal from contacting the concrete structure. The plastic surface of supporting block is used for preventing damage to paint of strobe during contact. 2 HPX pump rooms have set 8 storage rooms to store 16 strobes, which are 5.5m wide.
d） Drum-shaped filter screen
Drum-shaped filter screen shall comply with RCC-M Grade 3.
1）General
The drum-shaped filter screen is a rotating cylinder whose circle is installed with net slices. Water flows into the drum-shaped filter screen from ends on both sides and discharges outside along the circle after being filtered by the filter screen. When the drum-shaped filter screen rotates, the dirt interrupted by filter screen is brought onto the operation platform, washing it to a dump tank and draining it through drain. The rotating structure is composed of a drum-shaped filter screen frame, which is an outward-emitting spoke support through the hub installed on the main shaft. Both ends of main shaft are supported by an automatic center adjusting double-row sphere roller with spherical surface in bearing seat. In the bearing seat on one end of the main shaft, a brush-type feed mechanism of extra current cathode protection system is installed. Both sides of drum-shaped filter screen are set with a grease-box with alarming switch for low oil level. The exterior surface of filter screen is composed of separate and replaceable net slices which are fixed to the circle of drum-shaped filter screen framework by bolts and nuts.
During rotation, the drum-shaped filter screen is sealed by contact of flexible molding rubber seal plate with pressure plate and fastener installed on exterior of framework structure and low-friction seal plate installed on the fixed sealed angle steel on the wall of water chamber.
Dirt picking bucket is fastened onto the horizontal beam in drum-shaped filter screen for lifting large blocks of dirt. The railing is set on the passage to operation platform of backwashing device with a drum-shaped filter screen, and a stairway is built from passage of operation platform, anti splash housing, clearing dirty device to the working platform. The backwashing pipes installed in the anti splash housing are two pipelines of 100％ capacity, and it is possible to check and repair the nozzle when raising the cover of anti splash housing.
When the drum-shaped filter screen rotates, the net slices rotate across the dirt discharging bucket which is washed by the nozzle installed on fully wide net slices of drum-shaped filter screen. The nozzle is connected to the backwashing pipe by swift-changed joint, which is easy to clean and replace. The backwashing pipe is installed with a pressure measuring meter. The dirt accumulated in dirt discharging bucket and flushing water are discharged through concrete drainage. The rotation of drum-shaped filter screen is driven by pinions on transmission shaft of driving device and big gear ring in the central loop of drum-shaped filter screen framework. The transmission shaft is supported by a pair of separate roller bearings which are connected to the combined reducer, and the reducer is driven by an independent low-rate and a double-rate motor (middle/high rate). Additionally, there is a standby low-rate motor which is installed in reducer for emergency. Over loading protection of torque for driving device is realized by skip of electronic power monitor on a main panel installed at other where. The motor is equipped with moisture-proof heater in order to avoid the generation of negative potential when switching from high-rate to middle-rate or from middle-rate to low-rate. It is required to install a speed-measuring motor on each low-rate motor to gain a proportionate signal with driving speed. Before synchronized rotate speed is reached, the control system will harmonize and control to prevent low-rate motor switches on.
2） Data of plant site
Form of equipment Interior installation Filter media Seawater
Operation platform 8.50 m
Tidal levels of outer-sea are:
SEC designed highest tide level: 7.58m
CRF designed highest tide level: 4.54 m
CRF designed lowest tide level: -1.47m
SEC designed lowest tide level: -3.35m
The water levels of front tank（sea reservoir）of pump room are:
CRF designed lowest water level: -6.72m
SEC designed lowest water level: -8.00m
Elevation of central line of drum meshwork -1.0m*
Width of inlet channel 5.5m*
Elevation of bottom of inlet channel -11.5m*
Width of water chamber of intake chamber 6.0m*
Elevation of bottom of filter screen chamber -17.1m*
3） Hydraulic data
Flux 24.2m3/s*
Flow rate at water inlets
Flow rate through filter screen
Head loss of water intake
Head loss for going through filter screen
Loss of total head
4） Parameters of drum-shaped filter screen
Number of drum-shaped filter screen 8 sets（4 sets for each unit）
Diameter 22m*
The net width of civil construction structure of water chamber 6.0m*
Designed water level difference 2.0m
Diameter of mesh 3mm
Elevation of operational platform 8.0m*
Height of drum-shaped filter screen above operational platform 2m*
Number of flushing pipe 2
Diameter of flushing pipe mm
Flux of flushing water L/s
Hydraulic pressure in flushing pipe
5） Engineering material
Structure Carbon steel
Main shaft Forged carbon steel
Flushing water nozzle Stainless steel 316L
Flushing pipe Stainless steel 316L
2013.6.9