嵌縫纖維保證翻譯-中英對照
包裝
包裝必須符合JIS K6353 (自來水管件用橡膠制品作業)和JIS R3453 (石棉紙板),等的規定，并且適于水、水壓、溫度等的影響。
13.嵌縫對接
原則上，嵌縫對接必須符合JIS H21 10中規定的等級5(鉛錠)。
14.嵌縫纖維
原則上，嵌縫纖維是由130根單線包結合成一整體，直徑或者大約25毫米；
排水管裝置
a.總則
a1.存水彎的堵水深度為50毫米或大于50毫米，并且濾網疏水孔的總有效面積不少于排水管的橫截面積。
a2.如果使用鑄鐵材料，排水裝置材料必須符合JIS G5501(格雷鑄件鐵) 規定中的2級或高于2級；如果使用黃銅鑄件，必須符合JIS G5101(格雷鑄件鐵) 規定中的2級或高于2級。
a3.全部鑄件鐵使用合成樹脂完成冷涂裝，包含使用精煉瀝青材料。
a4.排水裝置的鍍鎳鉻部分必須JIS H8617(鎳鉻電鍍層)里的等級2類型1或類似標準。
b.地面排水管道存水彎
地面排水管道存水彎由鑄鐵制成，濾網使用黃銅鎳鉻鍍層. 瀝青防水層的地面排水管道存水彎必須使用防水類型材料，其它地面可以使用普通的類型材料。
c.洗滌存水彎
洗滌存水彎使用鑄鐵并使用黃銅或者不銹鋼(SUS 304)制成的內框. 這種濾網由黃銅鍍鎳鉻制成。
d. 地面清掃口
地面清掃口采用螺紋型黃銅表面鍍鎳銘層. 瀝青防水層的地面清掃口必須使用防水類型材料，其它地面可以使用普通的類型材料。
e底層地板清掃口
底層地板清掃口類型采用螺紋型黃銅材料。
f. 排水管裝置
排水管裝置使用黃銅表面鍍鎳銘層，鏈子和制動器為不銹鋼材料制成。
基坑和坑蓋
a. 總則
al.鐵鑄件的材料必須符合JIS G5501(格雷鐵鑄件)規定的3級或高于3級或同等標準。
a2.鐵鑄件必須經過精煉焦油烘焙，根據JIS K2473(焦油處理) 的規定，混合的亞麻籽油或者干性油必須超過百分之2，或者在瀝青材料使用精煉的合成樹脂進行冷涂裝。
b.仰拱基坑
b1.仰拱基坑必須為混凝土結構，并且全部可見部分必須經過薄層灰漿完成. 而且，基坑備有封蓋，在坑底部必須裝備有可以供管材直徑倒置裝置。
b2. 封蓋使用鑄鐵制成并附有索鏈，使用除臭類型材料，并且能承受2，500公斤的重量。
c.貯存基坑
c1.貯存基坑必須為混凝土結構，并且全部可見部分必須經過薄層灰漿完成. 而且，基坑備有封蓋，
c2. 封蓋使用鑄鐵制成并附有索鏈，使用除臭類型材料，并且能承受2，500公斤的重量。
SCOPE
This specification covers design, detailing, furnishing, fabricating, delivering and erecting miscellaneous and embedded metal components.
WORK INCLUDED
Design, detailing, furnishing, fabricating, delivering, unloading/handling, sorting, storing, protecting, removing from storage and erecting miscellaneous and embedded metal components. Scope includes but not necessarily limited to the following items.
- Welded grating
- Checkered steel floor plates.
- Stairs and treads
- Handrails
- Ladders
- Guard plates
- Embedded steel members, including steel door frames
- Banding of all openings in grating occasioned by field run piping.
- All materials necessary, including Type 316 stainless steel studs for
grating hold-down clips to connect miscellaneous metal components
to structural steel and to other parts of the structure already in place.
WORK NOT INCLUDED
Design, furnishing and installation of the following items are not included in this specification.
- Anchor bolts and anchor bolt sleeves into concrete foundations
- Ductwork
- Metal doors and pressed steel frames
- Pipe hangers, electrical equipment and duct supports
- Structural steel framing for buildings.
0310349
Revision 0 Part 4.4 - 320 PLTU Adipala (PLTU 2 Jawa Tengah)
1 x (600-700 MW) Location Cilacap
BOOK III
PART 4.4 Civil Works 4.4.3 Technical Specification
4.4.3.25.2 CODES AND STANDARDS
Bidder shall comply with the applicable requirements of the codes and standards published by the following organization:
AISC American Institute of Steel Construction
ANSI American National Standards Institute
AREA American Railway Engineering Association
ASTM American Society for Testing and Material
AWS American Welding Society
CDA Coper Development Association, USA
SSPC Steel Structures Painting Council, USA
UBC Uniform Building Code of USA
PPBBG Pedoman Perencanaan Bangunan Baja untuk
Gedung-1987
Conform especially to the'applicable provisions of the following codes and standards.
AISC Codes of Standard of Practice for Steel Buildings and
Bridges
AISC Specification for the Design Fabrication, and Erection
of Structural Steel for Buildings
AISC Specification for Structural Joints Using
ASTM 325 or A 490
ANSI B27.2 ASTM A 36
Bolts approved by Research Council on Riveted and Bolted Structural Joints of the Engineering Foundation
Plain Washers Structural Steel
ASTM A 123 Zinc (Hot-Galvanized) Coating on Products Fabricated from Rolled, Pressed, and Forged Steel Shapes, Plates, Bars, and Strip.
ASTM A 153 Zinc Coating (Hot-Dip) on Iron and Steel Hardware.
ASTM A167 Corrosion-Resisting Chromium-Nickel Steel Plate Sheet, and Strip.
2013.5.22