第五節 轉動機械的運行操作
一．離心泵的啟動、運行、維護與停運
1．泵啟動前的檢查
●　泵、電機周圍清潔，不允許任何雜物存放、妨礙泵的安全運行；
●　泵底座固定螺母牢固，電動機接地線良好；
●　泵的各部件連接牢固，手盤靠背輪正常自如；
●　轉動部位防護罩安全可靠；
●　軸承油室內油位正常（約2／3處），油質合格；
●　檢查水箱出口閥、泵的進口閥應在開啟位置，泵的出口閥應在關閉位置；
●　檢查泵的冷卻水，并調整至冷卻水流量合適；
2．離心泵的啟動、停運   
● 離心泵的啟動：   
按泵的“啟動”按鈕（可就地/遠方操作，選擇開關在MCC，啟停按鈕在MCC上或在就地電動機旁）

；
檢查轉動方向正確，壓力表是否指示正常及泵的振動正常；
待壓力穩定后，緩慢開啟泵的出口閥并調整至所需流量。
● 離心泵的停運
關閉泵的出口閥，按泵的“停止”按鈕（可就地/遠方操作，選擇開關在MCC，啟停按鈕在MCC上或

在就地電動機旁）；
水泵停運期間，室溫不應低于5℃，否則應放掉泵內積水，以防凍裂泵體。
電磁隔膜計量泵的啟動、停運
3． 計量泵的啟動：
●　打開所用計量箱出口閥，打開計量泵進、出口閥，打開該計量泵管路系統上所有閥門；
●　按計量泵的“啟動”按鈕啟動計量泵（可就地/遠方操作，選擇開關在MCC，啟停按鈕在MCC上

或在就地電動機旁）；
●檢查出口壓力表指示是否正常；
待出口壓力穩定后，調整泵的行程或脈沖頻率來調整泵的出力到所需流量。
● 計量泵的停運 ：
按計量泵的“停止”按鈕，停運計量泵（可就地/遠方操作，選擇開關在MCC，啟停按鈕在MCC上或

在就地電動機旁）；
關閉計量泵進、出口閥，如長時間停運還應關閉計量箱出口閥及系統上所開啟的閥門。
Section five Operation of rotation machinery
I. Start up, operation, maintenance and shut down of centrifugal pump
1. Inspection before pump startup
●Clean the area around pump and motor; it is prohibited to pile up any miscellaneous

articles or objects to affect the operation security of pump;
●The pump foundation shall be firmly fixed with nut; motor maintain good ground

connection;
●The connection of pump components shall be tightly fixed, the stick coupling shall

be operated under a normal condition;
●The covering of rotation area shall be safe and reliable;
●Bearing oil chamber is in a normal level (2/3 of the oil chamber); the oil material

is qualified;
●Check the outlet valve of water tank; the import valve of pump shall be in open

position; outlet valve of pump shall be in close position;
●Check the cooling water of pump and adjust the cooling water flow to an appropriate

level;

2. Startup and shut down of centrifugal pump
●Startup of centrifugal pump:   
Press the “start” button of pump (implement the local/remote operation; select

switch is in MCC; startup and shut down button is on MCC or nearby the local motor);
Check whether the rotation direction is correct; check whether the pressure gauge and

pump vibration is normal;
After the pressure is stable, slowly opens the outlet valve and adjust the pump to the

required current capacity.
●Shut down of centrifugal pump
Close the outlet valve of pump; press the “shut down” button of pump (local/remote

operation, select switch is in MCC; startup and shut down button is on MCC or nearby

the local motor);
The room temperature shall not be lower than5℃ during the water pump shut down

period; otherwise, it is required to discharge excess water in the pump for preventing

the cracks of pump body due to freezing.
The startup and shut down of electromagnetism film metering pump start, suspends

shipment

3. Startup of metering pump:
●Opens all outlet valve of metering tank; opens the inlet and outlet valve of

metering pump; opens o all valves on this metering pump pipeline;
●Press the “startup” button of metering pump (local/remote operation, select switch

is in MCC; startup and shut down button is on MCC or nearby the local motor);
●Check whether the indications of outlet pressure gauge is normal;
After the outlet pressure is stable, adjust the travel or pulse frequency to adjust

required current capacity of pump output.
●Shut down of metering pump
Press the “shut down” button of metering pump (local/remote operation, select switch

is in MCC; startup and shut down button is on MCC or nearby the local motor);
Closes the inlet and outlet valve of metering pump; it is required to close the outlet

valve of metering tank and the opening valve of system when the unit is not in use for

a long time.